Home > Shop By Brand > DC USA Approved Assa Abloy > DC USA Approved Assa Abloy Electric Strikes With No Frame Cutting Required > DC USA Approved Assa Abloy 8000 No Frame Cutting Electric Strike - Works With Cylindrical Locks With Latchbolts Up To 5/8" Throw
We found 8 results matching your criteria.

DC USA Approved Assa Abloy 8000 No Frame Cutting Electric Strike - Works With Cylindrical Locks With Latchbolts Up To 5/8" Throw



The DC USA Approved 8000 Series is a compact, high-performance electric strike featuring a unique concealed design for use with cylindrical locksets. No cutting on the frame is required. Simply remove the existing strike plate, adjust the vertical alignment feature to the latchbolt centerline, and install. Its strength is derived from a unique keeper pin locking design, enabling the 8000 to exceed the ratings of the frame, door and locking hardware. This field selectable fail secure/fail safe unit is easy to install and accommodates latchbolts up to 5/8" throw.

The 8000 Series is also available in a Complete One Box Solution:
  • 8000C Complete Pac
* Note: The change in model number from 5900 to 8000 highlights the increased compatibility of this premium line. Updated to ensure frame clearance in an even greater selection of frames, this product now fits within an ANSI frame prep set at all hinge and door spacings per SDI-129-04 with no frame interference.

Frame application

  • Metal
  • Wood
Electrical
  • .24 Amps at 12 VDC/VAC
  • .12 Amps at 24 VDC/VAC
  • DC continuous duty/AC intermittent duty only
Standard Features
  • No cutting on frame required
  • Vertical adjustability to accommodate door sag and misalignment
  • Tamper resistant
  • Static strength 1,500 lbs.
  • Dynamic strength 70 ft-lbs.
  • Endurance 500,000 cycles
  • Field selectable fail safe/fail secure
  • Dual voltage 12 or 24 VDC/VAC
  • Non-handed Internally mounted solenoid
  • Accommodates 1/2"-5/8" cylindrical latchbolt (5/8" with 1/8" door gap)
  • Strike body depth 1-1/16" Strike body width decreased to 1-7/16" to increase frame compatibility
  • Five year limited warranty
Optional Features
  • LBM - Latchbolt monitor
Finishes
  • 630 - Satin stainless steel
  • 605 - Bright brass
  • 606 - Satin brass
  • 612 - Satin bronze
  • 613 - Bronze toned
  • 629 - Bright stainless steel
  • BLK - Black
  • *Complete Pacs are only available in the 630 finish

Reduce your install time by evaluating your opening

The DC USA Approved 8000/8300 Electric Strikes can be adjusted to compensate for frame and door irregularities. Sometimes, adjusting the frame and door back to industry standards is not an option. Here are some tips to quickly compensate for frame twist and determine the condition of the latchbolt.

Measure Frame Twist
One way to measure frame twist is to place a carpenter square on the stop and the face of the door. If the angle is less than 90 degrees, the 45 degree ramp angle of the DC USA Approved 8000/8300 is steepened and may need to be corrected as shown (Figure 1). We recommend you check the condition of the latchbolt prior to installing the 8000/8300. Poorly constructed, worn out or damaged latchbolts may not slide along a ramp at any angle. To check the condition of your latchbolt, we recommend applying a slight force to the tip of the latchbolt (about 45 degrees to the door face). Make sure the latchbolt can be pushed up into the door.



Compensate for Frame Twist
When a frame is twisted, the relationship between the face of a closed door and of the inside face of the frame (i.e., rabbet) may not meet the 90 degree industry standard. Untrue frames and doors impact latchbolt wear and the force required to exit, so we recommend you ensure that the angle is between 90–95 degrees.



If manipulating the frame is not possible, we recommend placing several shims included under the top and bottom (stop side) of the faceplate (Figure 2). This effectively increases the 8000/8300 ramp angle and compensates for frame twist. You can also compensate for frame twist by placing shims under the top and bottom (bevel side) of the latchbolt (Figure 3).

Sort By:
Page of 1
DC USA Approved No Frame Cutting Electric Strike Body Only (Faceplates Not Included), 630 Satin Stainless Steel Finish DC USA Approved No Frame Cutting Electric Strike Body Only (Faceplates Not Included), 630 Satin Stainless Steel Finish Usually Ships 24-72 Hours
List Price: $430.60
Our Price: $215.30
Savings: $215.30