Compliance & Certifications

• ADA compliant approach, clearances, and operability
• IBC compliant storefront entrance assembly
• Hardware:Grade 1, UL Listed, and ANSI/BHMA certified (e.g., A156.4 closers, A156.5 locks/latches, A156.6 trim)
• Glazing: 1/4" tempered safety glass for commercial storefront use

Key Features

• Wide stile construction:5" vertical stiles for heavy-duty strength in high-traffic environments
• Door size (pair): 72" x 84" overall; two leaves nominally 36" x 84" each
• Glazing: 1/4" tempered safety glass, factory pre-glazed
• Finish: clear anodized, architectural-grade aluminum
• Security & operation: one active door with a commercial deadlock featuring a lock indicator, exterior key cylinder, and interior thumbturn; the inactive door uses upper and lower flush bolts that secure to the header and threshold when latched
• Weather performance: frame is fully weatherstripped; the inactive (flush-bolt) door includes high-quality pile weatherstripping at the meeting stile for a tight seal between doors when closed

What’s Included (Pre-Installed / Packaged)

• Alumitrex™ wide stile door pair, 72" x 84" overall (two 36" x 84" leaves)
• 1/4" tempered safety glass, factory pre-glazed with commercial glazing vinyl
• Heavy-wall aluminum rails and 5" stiles (clear anodized)
• Active door:Commercial deadlock with lock indicator, exterior key cylinder, and interior thumbturn (Grade 1, UL Listed, ANSI/BHMA certified)
• Inactive door:Upper & lower flush bolts with strikes for header and threshold engagement
• Closers: Two ADA hydraulic door closers (Grade 1, UL Listed, ANSI/BHMA A156.4 compliant)
• Pivots/Hinges: Heavy-duty pivot set or hinge set (ANSI/BHMA certified)
• Trim:Exterior pull and interior push bar on the active door (ANSI/BHMA A156.6 compliant)
• Weatherstripping:Full frame weatherstrip plus high-density pile weatherstrip along the inactive door meeting stile
• Threshold: Commercial aluminum threshold, prepped to accept lower flush bolt
• Fastener kit for storefront hardware components

All primary hardware components are Grade 1, UL Listed, and ANSI/BHMA certified for reliable performance.

Wall Type & Mounting (Exterior Block / CMU Wall)

Designed for exterior CMU block walls. Coordinate rough opening width/height with structural lintel or bond beam support as required. Integrate pan/threshold seal, flashing, and sealants with the water-resistive barrier and masonry details.

• Anchor frame to CMU using appropriate sleeve anchors, wedge/expansion anchors, or TAPCON-style masonry screws into solid or grouted cells (by installer)
• Use non-corroding masonry shims at manufacturer-recommended points to maintain plumb, level, and square
• Seal perimeter with commercial-grade backer rod and sealant compatible with masonry
• Verify smooth swing on both leaves, deadlock engagement on the active door, and flush bolt engagement at header/threshold on the inactive door

Masonry anchoring fasteners are not included, allowing the installer to select diameter and length appropriate to the CMU substrate and site conditions.

Specifications

• Nominal Size (Pair): 72" x 84"
• Configuration: Active / Inactive pair (inactive leaf with upper & lower flush bolts)
• Stile Width:5" vertical stiles (wide stile)
• Glazing: 1/4" tempered safety glass, pre-glazed
• Material/Finish: heavy-wall aluminum, clear anodized
• Hardware: Grade 1 UL Listed, ANSI/BHMA certified (closers, deadlock, pivots/hinges, trim, flush bolts)
• Weatherstripping: full-perimeter frame weatherstrip + pile meet-stile weatherstrip on inactive leaf
• Use: heavy-duty, high-traffic commercial entrances
• Origin: Made in USA
• Production: 3-4 week lead time

Quality & Packaging

• Factory pre-glazing and heavy-duty hardware prep to reduce install time
• Protective wrapping and heavy-duty crating for freight transit
• Installation instructions included

Notes

• Verify rough opening, lintel/bond beam support, and threshold transition prior to ordering
• Coordinate waterproofing, pan flashing, and perimeter sealant with site conditions
• Site-specific conditions may require alternate anchors or sealants (by installer)